Unit uv curing flexibility

The inter-unit curing device itself is equipped with a plug-in module, which takes 2 to 3 minutes to be replaced, and can be installed between the printing units. This production flexibility allows production backup. They are placed according to the needs of each job, to adapt to the needs of different ink colors, printing color sequence and ink coverage. The maximum number of modules is one UV module per print unit. It is possible to use fewer modules; it is recommended to use at least one module for every two print units.

The inter-unit desiccator was placed behind opaque white, metallic, printed colors 15% above standard density, and dark (black, blue, green) and printing units with ink coverage exceeding 80% of the plate. Specially modified inter-drier drying units can be used for opaque white.

When using conventional ink and dusting, remove the UV lamp from the delivery device. In order to avoid contamination, there is a false device that can be inserted as a safety device without the printer not being activated.

Non-classical UV (hybrid) inter-drier drying unit: UV printer end curing is not suitable for high-speed printing with high ink coverage. Tests have shown that printing low ink coverage on high gloss papers is sufficient after a final printing unit, but two units are required for printing high ink coverage on low gloss printing materials Inter-drying device.

UV coating end drying unit and case: For best results, the UV drying unit on the end of the press should be placed as close as possible to the delivery unit so that the varnish is spread as evenly as possible before curing.

If all printing units have an inter-unit UV docking station, there is complete production flexibility. The position of the existing inter-UV drying unit in these printing units can be changed according to the requirements of a given job (color sequence, brightness, and ink coverage).

Combined infrared + hot air + UV drying system

The drying device installed at the end of the printing press has an on-line coating unit and a UV device, which is used to rotate the printing process:

Hot air: used for waterborne, infrared (IR) lamps to heat water, produce water vapor, which is discharged by the hot air knife and discharged by the suction system.

Infrared part: Helps reduce the (normally offset) ink viscosity (not UV inks) and speeds the absorption of the substrate material.

UV section: Ensures final curing of UV inks (special UV and hybrid UV modes) and UV varnish.

Infrared unit drying device

The inter-infrared inter-drier drying device before the first glazing unit heats the printed sheets and helps to uniformly distribute the lacquer layer.

An infrared inter-drier drying device before the second coating unit dries the first coating and heats the printed sheets to help prevent the production of an orange peel surface (caused by the waterborne particles captured by the primer layer when using an aqueous primer). Causes the gloss to drop; too much energy only solidifies the surface).

Infrared inter-drier drying unit accelerates oxidative drying.

With the primer/UV process, it is possible to use an infra-red inter-drier drying unit to apply the module to the pre-heated sheet in the primer coating application process to help the primer dry.

Plastic Lobster Clasp

What is Lobster Clasp


Because the shape of the Plastic Lobster Clasp Hook resembles a lobster, so it is called Plastic Lobster Claw Clasp.

The Plastic Lobster Clasp, also known as Plastic Lobster Claw Clasp, is made by POM plastic material, it has lots of colors in stock, more colors can be customized as Pantone color number as well. Check if you are interested in any of these colors below:

Lobster Clasp Plastic


Product name: Plastic Lobster Clasp
material: plastic
Color: as picture, or customized color
Size: 18mm*25mm, 24mm*34.5mm or customized
MOQ: 1000PCS

Plastic Lobster Clasp Hook

Lobster Clasp Plastic



We have different colors of Plastic Lobster Clasps to choose from, the transparency is also different, if you have the color you want, you can contact us to customize.

Plastic Lobster Clasps



We have different sizes of Plastic Lobster Clasps, and we can also customize the size you need.

Plastic Lobster Claw


Lobster Clasp is very common in life and has a wide range of uses. Plastic Lobster Clasp is a popular style now. It is often used in key chains and mobile phone chains, and can be used in necklaces and various pendants.

FAQ

1. What's your best price for this plastic lobster clasp?
A: The price depends on the order requirements about size, color, qty, etc. pls contact our professional sales to get accurate quotation.

2.What's the delivery time?
A: Sample order will be delivered at 5-7 workdays,large order is 10-14 days after confirming the details

3.What's your packing?
A:Our usual packing for lobster clasp is 100pcs/opp bag, then packed in export carton

4.What about the warranty?
A: We are very confident in our products, each lobster clasp was tested ok here, and we pack them very well, so usually you will receive your order in good condition. But to avoid any subsequent trouble regarding quality issue, we suggest that you check the clear lobster clasp once you receive them,and let us know the details if there is any damaged ones, so that we can deal with it accordingly.

5.Does your factory audit?
Yes,our factory is audited by TüV Rheinland .


Welcome to customize your own Plastic Lobster Clasps!

Plastic Lobster Clasps,Lobster Clasp Plastic,Plastic Lobster Clasp Hook,Plastic Lobster Claw Clasp,Plastic Lobster Claw

Shenzhen Yiyixing Zipper Manufacture Co.,Ltd , https://www.yyxchina.com