The phenomenon of ink drop phenomenon is relatively low in the printing of paper self-adhesive materials, which is more common in film materials, mainly due to the unstable surface tension of film materials. Under normal circumstances, the reason why the film material is printed off ink is low surface tension of the film material, poor UV curing, and excessive use of the ink additive.
Low surface tension of film material leads to ink loss
In general, the surface tension of the film-like material needs to be more than 38 dynes to ensure normal printing, and to make the ink firmly adhered, it is required to reach 42 dynes or more. If the ink drop occurs during the printing process, you can use the Dyne pen to test the surface tension value of the material. If it is lower than the above standard, it is recommended to use the online corona or the method of coating the base oil to increase the surface tension of the film material. In order to achieve better ink adhesion.
If there are no conditions to solve the problem by the above two methods, you can also use low surface energy ink to try to solve. Many ink manufacturers currently offer inks specifically for low-surface energy materials, and printing companies can test to find an ink that matches the label material used to solve this problem.
Poor UV curing leads to ink loss
The ink drop also has a lot to do with the curing effect of the UV ink. If the power of the UV lamp is insufficient, or the printing speed is too fast, a "fake dry" phenomenon will occur, which can easily lead to ink loss. The so-called "fake dry" means that the surface layer of the ink has been dried/cured, and the inside is not completely dried/cured.
It should be particularly noted here that the ink drop caused by this phenomenon occurs mostly in the printing of large-area solid patterns. This is because the amount of ink used in the solid pattern is large, and the inside of the ink layer is not easily cured completely. In addition, sometimes the ink printed at the same time is only a certain color drop ink is more obvious, the most common is the black ink off the ink is serious. This is because UV light is more difficult to penetrate the black ink layer, and in most cases the black ink is arranged to be printed in the last color group, and the total curing time is the shortest and it is not easy to cure completely.
In case of such problems, you can first check if the UV lamp has exceeded the rated service life. If it is exceeded, you need to replace the lamp. If the UV lamp is in the normal service period, then the power of the UV lamp should be insufficient, and the power of the UV lamp can be appropriately increased, or the printing speed can be lowered.
However, for film-type self-adhesive materials, such processing may cause new problems - when the printing speed is too low or the UV lamp power is too high, it is likely to cause the film-type self-adhesive material to be subjected to heat per unit time. Larger and deformed.
In case of such problems, the ink supply amount can be appropriately reduced, and the printing speed or the power of the UV lamp can be appropriately increased to ensure the ink is completely cured. If the amount of ink supply is reduced, the printing on the ground is falsified, and if necessary, it can be solved by two printing methods.
Excessive use of ink additives leads to ink loss
The winter weather in the north is relatively cold. Some printing companies will encounter problems of thickening, viscous, and poor ink in the production process. Many operators will use the method of adding ink to increase the fluidity of the ink. However, once the varnish is added too much, it is easy to cause the ink to fall.
In general, the addition ratio of varnish is 3% to 5%, and if it exceeds this range, it needs to be carefully added.
The Training head made of high-temperature synthetic fiber Hair. All of the hair has been chemically washed and disinfected. If you want to flat/curl iron your hair, we recommend that the temperature can not exceed 150 degrees, and not exceed 15 seconds every time.
The Hair length is 26-28 inches (from the forehead to the back hair end), individual hair strand.
It is suitable for cosmetology students or anyone to practice straightening, cutting, curling, braiding, setting and marcel. But can not dye, bleach and make up.
An ideal choice for hairdressing students to practice, little girls to play game or as a teaching supplies for kindergarten or primary school.
The hair is implanted firmly on the braiding Mannequin Head to ensure there is nearly no losing hair. For first used, please comb the hair first; It is common for losing a little hair first time and won't happen the next time.
Our mannequin head with hair comes with with an adjustable clamp holder which allows an easy way for hair styling or to display wigs and hats which can be swiveled and clamped on desk.
Synthetic Training Head,Synthetic Hair Training Head,Cosmetology Practice Head,Hairdressing Mannequin Head
Xuchang Le Yi De Import And Export Trade Co., Ltd. , https://www.lileaderbeauty.com